Overview of materials for Polyetheretherketone, Unreinforced

Overview of materials for Polyetheretherketone, Unreinforced 物性表: Overview of materials for Polyetheretherketone, Unreinforced物性表及特性介紹,Overview of materials for Polyetheretherketone, Unreinforced注塑參數詳情,如需Overview of materials for Polyetheretherketone, Unreinforced下載, 可到相關下載區下載
  • 熔體流動速率 [g/10min]: 3.96
  • 密度 [g/cm3]: 1.23
  • 吸水率 [%]: 0.05
  • 缺口沖擊強度: 0.214
  • 拉伸強度 [MPa]: 89.6
  • 斷裂伸長率 [%]: 24.1
  • 彎曲強度 [MPa]: 80.0
  • 彎曲模量 [MPa]: 3.50
  • 硬度: 120.0
  • 脆化溫度 [℃]: -65.0
 
Physical PropertiesMetricEnglishComments
Density 1.23 - 1.65 g/cc0.0444 - 0.0596 lb/in3Average value: 1.33 g/cc Grade Count:60
Filler Content 0.000 - 30.0 %0.000 - 30.0 %Average value: 6.00 % Grade Count:5
Water Absorption 0.0500 - 0.500 %0.0500 - 0.500 %Average value: 0.198 % Grade Count:29
Moisture Absorption at Equilibrium 0.100 - 0.500 %0.100 - 0.500 %Average value: 0.289 % Grade Count:14
Water Absorption at Saturation 0.350 - 1.65 %0.350 - 1.65 %Average value: 0.582 % Grade Count:17
Particle Size 10.0 - 70.0 μm10.0 - 70.0 μmAverage value: 35.0 μm Grade Count:3
Viscosity 90000 - 450000 cP90000 - 450000 cPAverage value: 244000 cP Grade Count:5
 100000 - 500000 cP
@Temperature 400 - 400 °C
100000 - 500000 cP
@Temperature 752 - 752 °F
Average value: 307000 cP Grade Count:9
Linear Mold Shrinkage 0.00300 - 0.0180 cm/cm0.00300 - 0.0180 in/inAverage value: 0.00959 cm/cm Grade Count:22
Linear Mold Shrinkage, Transverse 0.00900 - 0.0130 cm/cm0.00900 - 0.0130 in/inAverage value: 0.0121 cm/cm Grade Count:11
Melt Flow 3.96 - 91.0 g/10 min3.96 - 91.0 g/10 minAverage value: 28.1 g/10 min Grade Count:9
Spiral Flow 7.60 - 850 cm2.99 - 335 inAverage value: 199 cm Grade Count:9
 
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell M 85.0 - 10985.0 - 109Average value: 101 Grade Count:20
Hardness, Rockwell R 120 - 127120 - 127Average value: 124 Grade Count:7
Hardness, Shore D 62.0 - 89.062.0 - 89.0Average value: 85.1 Grade Count:15
Ball Indentation Hardness 90.0 - 230 MPa13100 - 33400 psiAverage value: 192 MPa Grade Count:8
Tensile Strength, Ultimate 80.0 - 150 MPa11600 - 21800 psiAverage value: 102 MPa Grade Count:36
Tensile Strength, Yield 89.6 - 140 MPa13000 - 20300 psiAverage value: 102 MPa Grade Count:26
Elongation at Break 1.50 - 60.0 %1.50 - 60.0 %Average value: 23.7 % Grade Count:57
Elongation at Yield 2.00 - 6.00 %2.00 - 6.00 %Average value: 4.40 % Grade Count:8
Modulus of Elasticity 2.20 - 12.0 GPa319 - 1740 ksiAverage value: 4.54 GPa Grade Count:53
Flexural Yield Strength 24.1 - 210 MPa3500 - 30500 psiAverage value: 159 MPa Grade Count:51
 9.00 - 95.0 MPa
@Temperature 125 - 275 °C
1310 - 13800 psi
@Temperature 257 - 527 °F
Average value: 39.3 MPa Grade Count:6
Flexural Modulus 3.50 - 11.1 GPa508 - 1610 ksiAverage value: 4.69 GPa Grade Count:48
 0.20312 - 0.20312 GPa
@Temperature 204 - 204 °C
29.460 - 29.460 ksi
@Temperature 400 - 400 °F
Average value: 0.203 GPa Grade Count:1
Compressive Yield Strength 31.0 - 183 MPa4500 - 26500 psiAverage value: 108 MPa Grade Count:24
 65.0 - 70.0 MPa
@Temperature 120 - 120 °C
9430 - 10200 psi
@Temperature 248 - 248 °F
Average value: 69.2 MPa Grade Count:6
Compressive Modulus 2.48 - 4.14 GPa360 - 600 ksiAverage value: 3.31 GPa Grade Count:7
Shear Strength 53.0 - 80.0 MPa7690 - 11600 psiAverage value: 64.1 MPa Grade Count:5
 14.3411 - 68.2581 MPa
@Temperature 65.6 - 288 °C
2080.00 - 9900.02 psi
@Temperature 150 - 550 °F
Average value: 43.8 MPa Grade Count:1
Izod Impact, Notched 0.214 - 1.07 J/cm0.400 - 2.00 ft-lb/inAverage value: 0.518 J/cm Grade Count:24
Izod Impact, Unnotched 2.70 J/cm - NB5.06 ft-lb/in - NBAverage value: 15.8 J/cm Grade Count:6
Izod Impact, Notched (ISO) 0.450 - 9.50 kJ/m20.214 - 4.52 ft-lb/in2Average value: 4.63 kJ/m2 Grade Count:20
Izod Impact, Unnotched (ISO) NBNBGrade Count:20
Charpy Impact Unnotched 1.40 J/cm2 - NB6.66 ft-lb/in2 - NBAverage value: 15.7 J/cm2 Grade Count:11
Charpy Impact, Notched 0.0800 - 8.00 J/cm20.381 - 38.1 ft-lb/in2Average value: 1.31 J/cm2 Grade Count:15
Coefficient of Friction 0.110 - 0.5000.110 - 0.500Average value: 0.263 Grade Count:15
K (wear) Factor 40.3 - 755 x 10-8 mm3/N-M20.0 - 375 x 10-10 in3-min/ft-lb-hrAverage value: 612 x 10-8 mm3/N-M Grade Count:5
Limiting Pressure Velocity 0.210 - 0.660 MPa-m/sec6000 - 18800 psi-ft/minAverage value: 0.400 MPa-m/sec Grade Count:8
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 4.10e+10 - 4.90e+16 ohm-cm4.10e+10 - 4.90e+16 ohm-cmAverage value: 9.18e+15 ohm-cm Grade Count:31
 1.00e+9 - 1.00e+15 ohm-cm
@Temperature 125 - 275 °C
1.00e+9 - 1.00e+15 ohm-cm
@Temperature 257 - 527 °F
Average value: 5.00e+14 ohm-cm Grade Count:6
Surface Resistance 1.00e+6 - 1.80e+15 ohm1.00e+6 - 1.80e+15 ohmAverage value: 1.40e+14 ohm Grade Count:17
Dielectric Constant 2.80 - 10.92.80 - 10.9Average value: 3.51 Grade Count:27
 4.50 - 4.50
@Temperature 200 - 200 °C
4.50 - 4.50
@Temperature 392 - 392 °F
Average value: 4.50 Grade Count:1
 4.50 - 4.50
@Frequency 50000 - 50000 Hz
4.50 - 4.50
@Frequency 50000 - 50000 Hz
Average value: 4.50 Grade Count:1
Dielectric Strength 15.7 - 126 kV/mm400 - 3200 kV/inAverage value: 24.2 kV/mm Grade Count:25
Dissipation Factor 0.00100 - 0.5180.00100 - 0.518Average value: 0.0282 Grade Count:25
Comparative Tracking Index 150 V150 VAverage value: 150 V Grade Count:13
 
Thermal PropertiesMetricEnglishComments
CTE, linear 11.4 - 150 μm/m-°C6.33 - 83.3 μin/in-°FAverage value: 49.4 μm/m-°C Grade Count:30
 22.0 - 147.6 μm/m-°C
@Temperature 100 - 250 °C
12.2 - 82.00 μin/in-°F
@Temperature 212 - 482 °F
Average value: 98.0 μm/m-°C Grade Count:13
Specific Heat Capacity 1.85 - 2.20 J/g-°C0.442 - 0.526 BTU/lb-°FAverage value: 2.12 J/g-°C Grade Count:10
Thermal Conductivity 0.240 - 0.300 W/m-K1.67 - 2.08 BTU-in/hr-ft2-°FAverage value: 0.261 W/m-K Grade Count:21
Melting Point 334 - 386 °C633 - 726 °FAverage value: 343 °C Grade Count:48
Maximum Service Temperature, Air 230 - 315 °C446 - 599 °FAverage value: 270 °C Grade Count:29
Deflection Temperature at 1.8 MPa (264 psi) 140 - 315 °C284 - 599 °FAverage value: 176 °C Grade Count:40
Minimum Service Temperature, Air -100 - -20.0 °C-148 - -4.00 °FAverage value: -52.9 °C Grade Count:7
Brittleness Temperature -65.0 °C-85.0 °FAverage value: -65.0 °C Grade Count:4
Glass Transition Temp, Tg 143 - 148 °C289 - 298 °FAverage value: 144 °C Grade Count:30
UL RTI, Electrical 260 °C500 °FAverage value: 260 °C Grade Count:3
UL RTI, Mechanical with Impact 180 °C356 °FAverage value: 180 °C Grade Count:4
UL RTI, Mechanical without Impact 240 °C464 °FAverage value: 240 °C Grade Count:4
Flammability, UL94 V-0V-0Grade Count:43
Oxygen Index 23.0 - 49.0 %23.0 - 49.0 %Average value: 33.5 % Grade Count:19
Glow Wire Test 960 °C1760 °FAverage value: 960 °C Grade Count:5
 
Processing PropertiesMetricEnglishComments
Processing Temperature 100 - 400 °C212 - 752 °FAverage value: 331 °C Grade Count:12
Nozzle Temperature 360 - 395 °C680 - 743 °FAverage value: 378 °C Grade Count:8
Melt Temperature 340 - 400 °C644 - 752 °FAverage value: 372 °C Grade Count:10
Mold Temperature 163 - 250 °C325 - 482 °FAverage value: 193 °C Grade Count:15
Drying Temperature 120 - 150 °C248 - 302 °FAverage value: 139 °C Grade Count:13
Dry Time 3.00 hour3.00 hourAverage value: 3.00 hour Grade Count:5
 3.00 - 5.00 hour
@Temperature 120 - 150 °C
3.00 - 5.00 hour
@Temperature 248 - 302 °F
Average value: 4.00 hour Grade Count:4
Moisture Content 0.100 - 0.200 %0.100 - 0.200 %Average value: 0.150 % Grade Count:4
Injection Pressure 82.7 - 124 MPa12000 - 18000 psiAverage value: 103 MPa Grade Count:3

轉載請注明: 轉自中國塑膠原料之家 http://www.sgwanshunchem.com/wuxingbiao/

本文鏈接: http://www.sgwanshunchem.com/yuanliaoku/show-50421.html

免責聲明: 本文 Overview of materials for Polyetheretherketone, Unreinforced 僅代表作者個人觀點,中國塑膠原料之家無關。中國塑膠原料之家網所轉載的內容,其版權均由原作者和資料提供方所擁有!如因作品版權問題需要處理,請與我們聯絡

塑膠原料之家,專業塑料網站、原料報價網站,免費發布塑膠供求信息。塑膠原料之家為您提供塑料供應、塑料求購、塑料行情、塑料展會、塑料原料資訊服務。

2008-2015 塑料|塑膠原料|物性表大全|UL黃卡|SGS報告查詢|最新價格--塑膠原料之家

滬ICP備15027283號-4

她的小梨涡txt百度网盘下载